manualshive.com logo in svg

Hillrom Compella, Instructions For Use Manual

Share
Download
Hillrom Compella Instructions For Use Manual Download Page 101

Troubleshooting

Compella™ Bariatric Bed System Instructions for Use (178951 REV 6)

 87 

4.

When the problem is solved, press 

Reset Alarm

.

S

OLVE

 

A

 S

YSTEM

 A

LARM

 C

ONDITION

 

ON

 

A

 C

OMPELLA

™ F

OAM

 S

URFACE

If the unit detects an alarm condition in the air cells of the surface, an alarm

 

screen shows. Solve a 

system alarm condition as follows:

1.

Press 

Audio Pause

 to mute the alarm for 

10 minutes.

2.

Refer to the alarm screen to determine the 
alarm condition.

3.

Make sure the hoses are firmly connected 
to the air supply unit, and the air cells are 
free from leaks. If necessary, contact your 
facility-authorized maintenance person or 
Hill-Rom Technical Support.

4.

When the problem is solved, press 

Reset Alarm

.

S

URFACE

 

AND

 A

IR

 S

UPPLY

 U

NIT

—P

OWER

 F

AILURE

 

AND

 A

LARM

 C

ONDITIONS

NOTE:

The air supply unit 

must

 be plugged into AC power to operate.

Power Failure

A power failure can occur under these three conditions:

•

The air supply unit power cord was disconnected from the AC power outlet.

•

A power outage has occurred.

•

A fuse has blown.

During a power failure condition, the display is Off, and the air cells in the support surface will not 
inflate, but will hold air.

When power is restored, these occur:

•

The unit will resume operation in Pressure Redistribution mode.

•

The pressure settings that were stored in memory are restored.

•

The alarm settings will be restored automatically for a power loss that lasts 30 seconds or less.

NOTE:

The states of the Max Inflate, Audio Pause, and Lock buttons are not saved in memory during a power 
failure.

Alarm/Alert System

Different alarms are generated by the air supply unit to notify the caregiver of potentially hazardous 
conditions. The intended position of the caregiver to respond to alarms or alerts is standing in front of 
the air supply unit at the foot of the bed.

Summary of Contents for Compella





















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands