Hillenbrand Hill-Rom Advanta User Manual Download Page 41 | Manualshive

Page: 41 / 54

background image

Accessories

37

Accessories

Permanent IV Poles

The Permanent IV Poles option consists of two IV poles that support up to two IV pumps plus bags. The IV poles are
attached to the bed frame near the corners of the headboard. Each IV pole can support up to 40 lb (18 kg).

To Deploy:

• Lift the IV pole from its stored position behind the headboard and position it straight up.

• Make sure that the pole drops and locks into position.

• Raise the upper section of the pole to the desired height. The IV pole is ready for use.

To Store:

• Grasp and hold the upper section of the IV pole. Push the upper collar down, and lower the upper pole

section into the lower pole section.

• Lift the lower section of the IV pole up, and lower the pole down to the stored position behind the headboard.

The poles should rest in the storage slots provided on the bed frame.

CAUTION:
Do not exceed the 40 lb (18 kg) IV pole weight capacity.

CAUTION:
Do not mount infusion pumps on the lower section of an IV pole. Interference with head section articulation
could result.

Utility Shelf

The utility shelf accessory can be installed at the foot end of
the bed. The utility shelf measures 15" by 33" (38 cm x 84
cm), and can hold up to 45 lb (20 kg) of equipment.

Installation: Insert the ends of the utility shelf supports into

the IV pole support holes at the foot end of the
bed. Push down firmly to ensure the utility shelf
is fully seated.

Removal: Remove any equipment from the utility shelf.

Grasp the sides firmly and lift the utility shelf
and supports out of the IV pole support holes.

CAUTION:
Do not exceed the 45 lb (20 kg) utility shelf weight capacity.

Utility Shelf

«
...
39
40
41
42
43
...
»

Summary of Contents for Hill-Rom Advanta























































Reviews:

No comments

Related manuals for Hill-Rom Advanta

Brand: idiag Pages: 10

Brand: Bandit Pages: 136

Versaflo S Series

Brand: 3M Pages: 11

DBI Sala EXOFIT

Brand: 3M Pages: 32

Brand: 3M Pages: 8

Brand: Accurate Bio-Medical Technology Pages: 35

Brand: Ocmis Irrigazione Pages: 100

Brand: Kamikaze Pages: 112

Brand: KAM Pages: 2

Brand: Laser Pages: 2

Brand: Lars Thrane Pages: 50

Brand: Rain-Flo Irrigation Pages: 16

AirForm Night Splint

Brand: Össur Pages: 16

Brand: Össur Pages: 17

Brand: V-GREAT Pages: 4

Brand: Zafferano Pages: 28

Brand: Basler Pages: 33

Brand: Elma Pages: 35

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands