manualshive.com logo in svg

Hill-Rom MC700, Replacement Instructions Manual

Share
Download
Hill-Rom MC700 Replacement Instructions Manual Download Page 1

© 2014 by Hill-Rom Services, Inc. ALL RIGHTS RESERVED.
No part of this text shall be reproduced without written permission from Hill-Rom Services, Inc.
June 23, 2014

187155 REV 1

Page 1 of 10 

Hill-Rom® MC700 General Ward Bed—
Central Brake System Replacement Instructions

Tools required:

Hex wrench, 3mm

Hex wrench, 4mm

Flat head screwdriver

Needle nose pliers

Rubber mallet

Torque wrench

Parts required:

(1)

713528

Hex bar foot end

(1)

713529

Hex bar head end

(1)

710526

Central rod link weldment 

(1)

710075

Transmission lever 

(1)

172134

Transmission lever bariatric

(4)

187063

Bushing

(2)

711079

Grub screw

(2)

710066

Helmut cap

Removal

1.

Adjust the bed height to access the base frame.

2.

Set the brakes to Steer.

3.

At the 

foot

 end, loosen, but do not remove, the grub screws (A, B) from the brake ped-

als (see figure 1).

Figure 1.  Foot End Brake Pedal Screws

4.

Set the brakes to Neutral.

Summary of Contents for MC700











Reviews:

No comments

Brands by name

Popular brands

Load more brands