HIKVISION HiWatch HWI-B120H-U User Manual Download Page 72

Page: 72 / 193

Network Camera User Manual

Network Settings

Purpose:

Follow the instructions in this chapter to configure the basic settings and advanced

settings.

Configuring Basic Settings

Purpose:

You can configure the parameters, including TCP/IP, DDNS, PPPoE, Port, and NAT,

etc., by following the instructions in this section.

Configuring TCP/IP Settings

Purpose:

TCP/IP settings must be properly configured before you operate the camera over

network. The camera supports both the IPv4 and IPv6. Both versions can be

configured simultaneously without conflicting to each other, and at least one IP

version should be configured.

Steps:

Enter TCP/IP Settings interface:

Configuration > Network > Basic

Settings > TCP/IP

Summary of Contents for HiWatch HWI-B120H-U


































































































































































































Search results

Summary of Contents for HiWatch HWI-B120H-U

Reviews:

Related manuals for HiWatch HWI-B120H-U

Brands by name

Popular brands

HIKVISION HiWatch HWI-B120H-U, User Manual

Search results

Summary of Contents for HiWatch HWI-B120H-U

Reviews:

Related manuals for HiWatch HWI-B120H-U

Brands by name

Popular brands