manualshive.com logo in svg

HIKVISION DS-M5504HNI Series, User Manual

Share
Download
HIKVISION DS-M5504HNI Series User Manual Download Page 58

Mobile Network Video Recorder User Manual 

57 

Chapter 8 

 

Other Functions

 

8.1

 

Local Network Settings 

Steps:

 

1.

 

Enter the Local Network Settings interface. 

Menu>Basic Settings>Network 

 

Figure 8. 1

 

Local Network Settings 

 

2.

 

Input  the  device  IP  address,  subnet  mask,  default  gateway,  DNS  server  address  and  download  server  IP  in  the 

corresponding text fields. 

 

 

The IP address of the device should be unique in the network and the default value is 192.0.0.64. 

 

The download server IP should be set when you upload the record files to the designate server. 

3.

 

Click the 

Set

 button of NTP, and you can configure the NTP (Network Time Protocol) settings for the device. 

Perform the following steps to configure the NTP settings: 

1)

 

Check the checkbox of 

NTP

 to enable the NTP settings. 

2)

 

Input the interval of time synchronization. 

3)

 

Input the IP address of NTP server. 

4)

 

Click 

OK 

to save the new settings and exit. 

Summary of Contents for DS-M5504HNI Series















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands