background image

Tri-pod Turnstile • User Manual 

 

17 

Chapter 4 Daily maintenance and trouble shooting 

4.1 Maintenance 

1)

 

General indications 

  The tripod turnstile should be inspected and cleaned at regular intervals in order to maintain 

the components in good working order and to check for signs of wear. The following indications 
refer  to  the  installation  where  the  average  number  of  transits  per  year  is  equal  to  two  million. 
When  the  tripod  turnstile  is  used  in  a  dusty  area,  the  regular  interval  for  inspection  should  be 
shortened. If used in the subway or the light rail station, the inspection interval is recommended 
to be 6 months. The users are also encouraged to determine the interval according to their own 
situation. 

To avoid the risk of electric shock, always ensure that the electrical power is disconnected 

before inspecting the mechanism. 
2)

 

Component 

Lock  arms  and  solenoids  (Operation  to  be  carried  out  with  the  power  supply 

disconnected.): —Grease the pins of the lock arms that slide on the solenoid shaft.—Grease the 
solenoid shaft and spring, and do not grease  the core of the solenoid—check that the shaft/lock 
arm assembly moves freely. 
3)

 

Oil pressure of the damper 

Operation  should  be  carried  out  with  the  power  supply  disconnected

  --check  whether  the 

damper oil spills; --check whether the force exerted by the spring is enough

  -- The force exerted 

by the spring should match that exerted by the damper. Generally speaking, the former need to be 
slightly more powerful. 
4)

 

Upper positioning cam 

Operation should be carried out with the power supply disconnected.—Loosen the spring of 

the positioning lever.—Check the guide way in the cam is clean and not excessively worn. –check 
some metal powder or the like sticks to the solenoid—Check the guide pin of the positioning lever 
for excessive play.—Check the magnetic strip is perfectly attached to the edge of the cam——Refit 
the cam -- adjust the spring of the positioning lever. 
5)

 

Tripod   

Operation should be carried out with the power supply disconnected. Check tightness of the 

three securing the base plate to the mechanism shaft. 
6)

 

Emergency Drop Arm Device 

Clean  all  dust  from  the  arm  detents,  the  arm  drop  lever  and  the  relative  solenoid.  Do  not 

lubricate these parts. 
7)

 

Cable and Connectors 

Operation should be carried out with the power supply disconnected

 

--Check that the wire connectors are firmly attached. 
--Check that the terminals are fully tightened. 
--Check that the insulation of the wires is in good condition and that no conductors are exposed. 

 

Summary of Contents for DS-K3G4402 Series






















Reviews:

Related manuals for DS-K3G4402 Series