HIKVISION DS-K3B961TX Series User Manual Download | Manualshive

Page: 115 / 126

background image

3. Select an access control device in the device list and click Wiegand to enter the Wiegand

Settings page.

4. Set the switch to on to enable the Wiegand function for the device.
5. Select the Wiegand channel No. and the communication mode from the drop-down list.

Note

If you set Communication Direction as Sending, you are required to set the Wiegand Mode as

Wiegand 26 or Wiegand 34.

6. Click Save.

●

The configured parameters will be applied to the device automatically.

●

After changing the communication direction, the device will reboot automatically.

Enable M1 Card Encryption

M1 card encryption can improve the security level of authentication.
Steps

Note

The function should be supported by the access control device and the card reader.

1. Enter the Access Control module.
2. On the navigation bar on the left, enter Advanced Function → More Parameters .
3. Select an access control device in the device list and click M1 Card Encryption to enter the M1

Card Encryption page.

4. Set the switch to on to enable the M1 card encryption function.
5. Set the sector ID.

The sector ID ranges from 1 to 100.

6. Click Save to save the settings.

8.8 Door/Elevator Control

In Monitoring module, you can view the real-time status of the doors or elevators managed by the

added access control device. You can also control the doors and elevators such as open/close the

door, or remain the door open/closed via the client remotely. The real-time access event are

displayed in this module. You can view the access details and person details.

Note

For the user with door/elevator control permission, the user can enter the Monitoring module and

control the door/elevator. Or the icons used for control will not show. For setting the user

permission, refer to .

DS-K3B961TX Series Swing Barrier User Manual

102

«
...
113
114
115
116
117
...
»

Summary of Contents for DS-K3B961TX Series































































































































Reviews:

No comments

Related manuals for DS-K3B961TX Series

Brand: GiBiDi Pages: 40

Brand: tousek Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands