HIKVISION DS-K3B961TX Series User Manual Download

Page: 106 / 126

Note

●

For the card related functions(the type of access control card/multi-factor authentication), only

the card(s) with access group applied will be listed when adding cards.

●

The advanced functions should be supported by the device.

●

Hover the cursor on the Advanced Function, and then Click to customize the advanced

function(s) to be displayed.

8.7.1 Configure Device Parameters

After adding the access control device, you can configure the parameters of access control device

(access controller), access control points (door or floor), alarm inputs, alarm outputs, card readers

and lane controller.

Configure Parameters for Access Control Device

After adding the access control device, you can configure its parameters, including overlaying user

information on picture, uploading pictures after capturing, saving captured pictures, etc.
Before You Start

Add access control device to the client.
Steps
1. Click Access Control → Advanced Function → Device Parameter .

Note

If you can not find Device Parameter in the Advanced Function list, hover the cursor on the

Advanced Function, and then Click to select the Device Parameter to be displayed.

2. Select an access device to show its parameters on the right page.
3. Turn the switch to ON to enable the corresponding functions.

Note

●

The displayed parameters may vary for different access control devices.

●

Some of the following parameters are not listed in the Basic Information page, click More to

edit the parameters.

RS-485 Comm. Redundancy

You should enable this function if you wire the RS-485 card reader to the access control

device redundantly.

Display Detected Face

Display face picture when authenticating.

Display Card Number

DS-K3B961TX Series Swing Barrier User Manual

Summary of Contents for DS-K3B961TX Series































































































































Search results

Summary of Contents for DS-K3B961TX Series

Reviews:

Related manuals for DS-K3B961TX Series

Brands by name

Popular brands

HIKVISION DS-K3B961TX Series, User Manual

Search results

Summary of Contents for DS-K3B961TX Series

Reviews:

Related manuals for DS-K3B961TX Series

Brands by name

Popular brands