manualshive.com logo in svg

HIKVISION DS-K3B601S Series, User Manual

Looking for a User Manual for your HIKVISION DS-K3B601S Series? Look no further! Get this essential manual for free, allowing you to maximize your product's potential. Simply visit manualshive.com to download it instantly. Unlock the full potential of your HIKVISION DS-K3B601S Series with this detailed manual.

Share
Download
background image

Appendix F. Communication Matrix and Device

Command

Communication Matrix

Scan the following QR code to get the device communication matrix.

Note that the matrix contains all communication ports of Hikvision access control and video

intercom devices.

Figure F-1 QR Code of Communication Matrix

Device Command

Scan the following QR code to get the device common serial port commands.

Note that the command list contains all commonly used serial ports commands for all Hikvision

access control and video intercom devices.

Figure F-2 Device Command

DS-K3B601SX Series Swing Barrier User Manual

109

Summary of Contents for DS-K3B601S Series





























































































































Reviews:

No comments

Related manuals for DS-K3B601S Series

V2 BY Series Instructions Manual preview
BY Series
Brand: V2 Pages: 146
Aprimatic PARK 30 Instructions For Installation, Use And Maintenance Manual preview
PARK 30
Brand: Aprimatic Pages: 11

Brands by name

Popular brands

Load more brands