manualshive.com logo in svg

HIKVISION DS-7608NI-I2/8P, User Manual, Page: 98 / 221

Share
Download
HIKVISION DS-7608NI-I2/8P User Manual Download Page 98

I Series Network Video Recorder User Manual, 030117NA 

97 

Table 17 – Detailed Explanation of Picture-Playback Toolbar 

Button 

Function 

Button 

Function 

Button 

Function 

Button 

Function 

 

Play reverse 

 

Play 

 

Previous picture 

 

Next picture 

 

7.2

 

Playback Auxiliary Functions 

7.2.1.

 

Playing Back Frame-by-Frame 

Play video files frame-by-frame, to check image details of the video when abnormal events happen. 

7.2.1.1 

Using a Mouse 

1.

 

Go to Playback interface. 

2.

 

If you choose playback of the record file: click 

  button until the speed changes to 

single frame. One click on the playback screen will play back one frame. 

3.

 

If you choose reverse playback of the record file: click 

  button until the speed changes 

to single frame. One click on the playback screen will reverse play back one frame. It is 
also possible to use the 

  button in the toolbar. 

NOTE:

 

You can also advance/reverse single frames by using the mouse wheel. 

7.2.1.2 

Using the Front Panel 

1.

 

Click the 

  button to set the speed to single frame. One click on the 

  button, or one 

click on the playback screen or Enter button on the front panel, will play back or reverse 
play back one frame. 

7.2.2.

 

Thumbnails View   

Use the playback interface thumbnail views to locate the required video files on the time bar.   

NOTE:

  This feature is supported by cameras of 6 MP or less. 

1.

 

Enter the playback interface and start to play the video files. 

Summary of Contents for DS-7608NI-I2/8P






























































































































































































































Reviews:

No comments