HIKVISION DS-7608NI-I2/8P User Manual Download Page 97

Page: 97 / 221

I Series Network Video Recorder User Manual, 030117NA

7.1.9.2

Playing Back Pictures

Captured pictures stored in the device’s HDDs can be searched and viewed.

Enter Playback interface, Menu > Playback.

Select

Picture

from the drop-down list in the upper-left corner of the page to enter the

Picture Playback interface.

Check

checkbox to select channel(s) and specify search start time and end time.

Click

Search

to enter Search Result interface.

NOTE:

Up to 4,000 pictures can be displayed each time.

Choose a picture you want to view and click the

button.

Click

Back

to return to the search interface.

Figure 113 Picture Playback Result

Use the toolbar in the bottom section of the Playback interface to control playback.

Figure 114 Picture Playback Toolbar

Summary of Contents for DS-7608NI-I2/8P






























































































































































































































Search results

Summary of Contents for DS-7608NI-I2/8P

Reviews:

HIKVISION DS-7608NI-I2/8P, User Manual, Page: 97 / 221

Search results

Summary of Contents for DS-7608NI-I2/8P

Reviews: