manualshive.com logo in svg

HIKVISION DS-7608NI-I2/8P, User Manual, Page: 94 / 221

Share
Download
HIKVISION DS-7608NI-I2/8P User Manual Download Page 94

I Series Network Video Recorder User Manual, 030117NA 

93 

 

Figure 108 Sub-Periods Playback Interface 

NOTE: 

According to the defined number of split-screens, the video files on the selected date 
can be divided into average segments for playback (e.g., if there are video files 
existing between 16:00 and 22:00, and 6-screen display mode is selected, then it can 
play the video files for 1 hour on each screen simultaneously). 

 

7.1.8.

 

Playing Back by System Logs 

Play back record file(s) associated with channels after searching system logs. 

1.

 

Enter Log Information interface, Menu > Maintenance > Log Information. 

2.

 

Click

 Log Search

 tab to enter Playback by System Logs. 

3.

 

Set search time and type and click 

Search

 button. 

Summary of Contents for DS-7608NI-I2/8P






























































































































































































































Reviews:

No comments