HIKVISION DS-7608NI-I2/8P User Manual Download Page 85

Page: 85 / 221

I Series Network Video Recorder User Manual, 030117NA

7.1.2.3

Playback Interface

You can use the toolbar in the bottom part of the Playback interface to control playing progress,
as shown in Figure 96.

Figure 96 Playback Interface

Click the channel(s) to execute simultaneous playback of multiple channels.

Figure 97 Playback Toolbar

NOTE:

The

indicates the start/end time of the recorded

video files.

The

indicates the smart playback time bar and the

indicates the

normal playback time bar.

Playback progress bar: use the mouse to click any point of the progress bar to
display a thumbnail. Click on the thumbnail to jump to that period. You can also
drag the progress bar to locate specific frames.

Summary of Contents for DS-7608NI-I2/8P






























































































































































































































Search results

Summary of Contents for DS-7608NI-I2/8P

Reviews:

HIKVISION DS-7608NI-I2/8P, User Manual, Page: 85 / 221

Search results

Summary of Contents for DS-7608NI-I2/8P

Reviews: