manualshive.com logo in svg

HIKVISION DS-7608NI-I2/8P, User Manual, Page: 83 / 221

Share
Download
HIKVISION DS-7608NI-I2/8P User Manual Download Page 83

I Series Network Video Recorder User Manual, 030117NA 

82 

Chapter 7

 

Playback 

7.1

 

Playing Back Record Files 

7.1.1.

 

Instant Playback   

Play back the recorded video files of a specific channel in live view mode. Channel switch is supported. 

7.1.1.1 

Instant Playback by Channel 

Choose a channel in live view mode and click the 

  button in the quick setting toolbar. 

NOTE:

 

In instant playback mode, only files recorded during the last five minutes on this 
channel will be played back. 

 

Figure 93 Instant Playback Interface 

7.1.2.

 

Playing Back by Normal Search   

7.1.2.1 

Playback by Channel 

1.

 

Enter the Playback interface.

 

2.

 

Right click a channel in live view mode and select Playback from the menu, as shown in 
Figure 94. 

Summary of Contents for DS-7608NI-I2/8P






























































































































































































































Reviews:

No comments