manualshive.com logo in svg

HIKVISION DS-7608NI-I2/8P, User Manual, Page: 65 / 221

Share
Download
HIKVISION DS-7608NI-I2/8P User Manual Download Page 65

I Series Network Video Recorder User Manual, 030117NA 

64 

Chapter 6

 

Recording and Capture Settings 

6.1

 

Configuring Parameters 

You can define the parameters that affect the image quality such as transmission stream type, resolution, etc. 

NOTE:

 

Picture capture is supported by DS-9600/7700NI Series NVRs only.

 

6.1.1.

 

Before You Start 

1.

 

Make sure that the HDD has already been installed. If not, install a HDD and initialize it (Menu > 
HDD > General). 

 

Figure 61 HDD, General 

2.

 

Click 

Storage Mode

 to check the storage mode of the HDD.   

•  If the HDD mode is 

Quota

, set the maximum record capacity and maximum picture capacity. For 

detailed information, see 

Chapter

 

Configuring Quota Mode.

 

•  If the HDD mode is 

Group

, set the HDD group. For detailed information, see 

Chapter Configuring 

HDD Group for Recording and Capture.

 

 

Figure 62 HDD, Advanced 

3.

 

Enter the Record settings interface to configure the recording parameters, Menu > Record 
Configuration > Parameters. 

Summary of Contents for DS-7608NI-I2/8P






























































































































































































































Reviews:

No comments