manualshive.com logo in svg

HIKVISION DS-7608NI-I2/8P, User Manual, Page: 62 / 221

Share
Download
HIKVISION DS-7608NI-I2/8P User Manual Download Page 62

I Series Network Video Recorder User Manual, 030117NA 

61 

5.2.9.

 

Calling Linear Scan 

Follow the procedure to call the linear scan in the predefined scan range. 

NOTE:

 

Before operating this function, make sure the connected camera supports the linear scan and is in 
HIKVISION protocol.   

1.

 

Click the button 

PTZ

 in the lower-right corner of the PTZ setting interface, or press the PTZ button on 

the front panel, or click the PTZ Control icon 

  in the quick setting bar to enter the PTZ setting 

menu in live view mode. 

2.

 

Click the 

  button to show the one-touch function of the PTZ control. 

 

Figure 58 PTZ Panel, One-Touch 

3.

 

Click 

Linear Scan 

button to start the linear scan and click the Linear Scan button again to stop it. 

4.

 

You can click the 

Restore

 button to clear the defined left limit and right limit data. The dome needs to 

reboot for settings to take effect. 

5.2.10.

 

One-Touch Park 

Certain speed dome models can be configured to start a predefined park action (scan, preset, patrol, etc.) 
automatically after a period of inactivity (park time). 

NOTE:

 

Before operating this function, make sure the connected camera supports the linear scan and 
is set to HIKVISION protocol. 

1.

 

Click the 

PTZ

 button on the PTZ setting interface, press front panel PTZ button, or click PTZ Control 

icon 

  in the quick setting bar to enter the PTZ setting menu in live view mode. 

2.

 

Click the 

  button to show the one-touch function of the PTZ control. 

Summary of Contents for DS-7608NI-I2/8P






























































































































































































































Reviews:

No comments