manualshive.com logo in svg

HIKVISION DS-7608NI-I2/8P, User Manual, Page: 44 / 221

Share
Download
HIKVISION DS-7608NI-I2/8P User Manual Download Page 44

I Series Network Video Recorder User Manual, 030117NA 

43 

 

Figure 33 Password Configuration of the Camera 

3.

 

Click 

OK

 to save the settings and exit the interface. 

3.5.4.2 

Configuring Custom Protocols 

To connect network cameras that are not configured with standard protocols, you can 
configure customized protocols for them.   

There are 16 customized protocols provided in the system: you can edit the protocol name and 
choose whether to enable the sub-stream. 

1.

 

Click the 

Protocol

 button in the custom adding IP camera interface to enter the protocol 

management interface.

 

 

Figure 34 Protocol Management Interface 

2.

 

Choose the protocol type of transmission and choose the transfer protocols. 

NOTE:

 

Before customizing the protocol for the network camera, contact the manufacturer of 

Summary of Contents for DS-7608NI-I2/8P






























































































































































































































Reviews:

No comments