HIKVISION DS-7608NI-I2/8P User Manual Download Page 201

Page: 201 / 221

I Series Network Video Recorder User Manual, 030117NA

200

Figure 271 Edit User (Operator/Guest)

Figure 272 Edit User (admin)

Edit the password for the user.

•

Operator and Guest

– You can edit the user information, including user name, password,

permission level, and MAC address. Check the

Change Password

checkbox if you want to

change the password, and input the new password in the

Password

text field and press

Confirm

A strong password is recommended.

•

Admin

– You are allowed only to edit the password and MAC address. Check the

Change

Password

checkbox if you want to change the password. Input the correct old password, then the

new password in the

Password

text field, the press

Confirm

Summary of Contents for DS-7608NI-I2/8P






























































































































































































































Search results

Summary of Contents for DS-7608NI-I2/8P

Reviews:

HIKVISION DS-7608NI-I2/8P, User Manual, Page: 201 / 221

Search results

Summary of Contents for DS-7608NI-I2/8P

Reviews: