HIKVISION DS-7608NI-I2/8P User Manual Download Page 194

Page: 194 / 221

I Series Network Video Recorder User Manual, 030117NA

193

Figure 262 General Settings Interface (DS-9600NI)

Figure 263 General Settings Interface (DS-7700NI)

Configure the following settings:

• Language:

The default language used is English.

• Output Standard:

Set to NTSC or PAL, which must be the same as the video input standard.

• Resolution:

For DS-9600NI Series NVRs, you can configure the VGA/HDMI resolution and VGA2/HDMI 2

resolution. Up to 4K (3840 × 2160) resolution is selectable for VGA/HDMI output.

For DS-7700NI Series NVRs, you can configure the VGA resolution and HDMI resolution respectively. Up
to 4K (3840 × 2160) resolution is selectable for the HDMI output.

Summary of Contents for DS-7608NI-I2/8P






























































































































































































































Search results

Summary of Contents for DS-7608NI-I2/8P

Reviews:

HIKVISION DS-7608NI-I2/8P, User Manual, Page: 194 / 221

Search results

Summary of Contents for DS-7608NI-I2/8P

Reviews: