HIKVISION DS-7608NI-I2/8P User Manual Download Page 186

Page: 186 / 221

I Series Network Video Recorder User Manual, 030117NA

185

Figure 251 Image Settings Interface

Select the camera to set image parameters.

Adjust the slider or click on the up/down arrow to set the value of the brightness, contrast, or saturation.

Select the Enable Rotate function to Clockwise 270 degrees or OFF. When OFF is selected, the image is
restored to original.

Select the Mirror Mode to Left-Right, Up-Down, Center or OFF. When OFF is selected, the image is restored to
original.

NOTES:

The Rotate and Mirror functions must be supported by the connected IP camera.

The image parameters adjustment can affect both the live view and the recording quality.

Click the Apply button to save the settings.

Summary of Contents for DS-7608NI-I2/8P






























































































































































































































Search results

Summary of Contents for DS-7608NI-I2/8P

Reviews:

HIKVISION DS-7608NI-I2/8P, User Manual, Page: 186 / 221

Search results

Summary of Contents for DS-7608NI-I2/8P

Reviews: