HIKVISION DS-7608NI-I2/8P User Manual Download Page 184

Page: 184 / 221

I Series Network Video Recorder User Manual, 030117NA

183

Chapter 15

Camera Settings

15.1

Configuring OSD Settings

You can configure the camera’s OSD (On-screen Display) settings, including date/time, camera name, etc.

Enter the OSD Configuration interface, Menu > Camera > OSD.

Select the camera to configure OSD settings.

Edit the Camera Name in the text field.

Configure the Display Name, Display Date, and Display Week by clicking the checkbox.

Select the Date Format, Time Format, and Display Mode.

Figure 248 OSD Configuration Interface

You can use the mouse to click and drag the text frame on the preview window to adjust the OSD position.

Click the Apply button to apply the settings.

15.2

Configuring Privacy Mask

You are allowed to configure the four-sided privacy mask zones that cannot be viewed by the operator. The privacy
mask can prevent certain surveillance areas to be viewed or recorded.

Enter the Privacy Mask Settings interface, Menu > Camera > Privacy Mask.

Select the camera to set privacy mask.

Click the Enable Privacy Mask checkbox to enable this feature.

Summary of Contents for DS-7608NI-I2/8P






























































































































































































































Search results

Summary of Contents for DS-7608NI-I2/8P

Reviews:

HIKVISION DS-7608NI-I2/8P, User Manual, Page: 184 / 221

Search results

Summary of Contents for DS-7608NI-I2/8P

Reviews: