Home
/
HIKVISION
/
DS-7608NI-I2/8P
/
User Manual

HIKVISION DS-7608NI-I2/8P, User Manual, Page: 174 / 221

Share

Page: 174 / 221

HIKVISION DS-7608NI-I2/8P User Manual Download Page 174

I Series Network Video Recorder User Manual, 030117NA

173

Figure 227 Add IP SAN Disk

6.

After having successfully added the NAS or IP SAN disk, return to the HDD Information menu. The added
NetHDD will be displayed in the list.

NOTE:

If the added NetHDD is uninitialized, select it and click the Init button for initialization.

Figure 228 Initialize Added NetHDD

14.3

Managing eSATA

When there is an external eSATA device connected to the NVR, you can configure the eSATA for the use of
Record/Capture or Export, and you can manage the eSATA in the NVR.

1.

Enter the Advanced Record Settings interface, Menu > Record > Advanced.

2.

Select the eSATA type to Export or Record/Capture from the drop-down list of eSATA.

• Export:

Use the eSATA for backup. Refer to Backup using eSATA HDDs in Chapter

Backing Up by Normal

Video/Picture

Search for operating instructions.

• Record/Capture:

Use the eSATA for record/capture. Refer to the following steps for operating instructions.

Figure 229 Set eSATA Mode

3.

When the eSATA type is selected as Record/Capture, enter the HDD Information interface, Menu > HDD >
General.

«
...
172
173
174
175
176
...
»

Summary of Contents for DS-7608NI-I2/8P






























































































































































































































Reviews:

No comments