HIKVISION DS-7608NI-I2/8P User Manual Download Page 166

Page: 166 / 221

I Series Network Video Recorder User Manual, 030117NA

165

Figure 209 Create Array Interface

Edit the Array Name; set the RAID Level to RAID 0, RAID 1, RAID 5, RAID 6, or RAID 10; select the
Physical Disk that you want to configure array.

NOTES:

If you choose RAID 0, at least two HDDs must be installed.

If you choose RAID 1, two HDDs need to be configured for RAID 1.

If you choose RAID 5, at least three HDDs must be installed.

If you choose RAID 6, at least four HDDs must be installed.

If you choose RAID 10, the number of HDDs installed should be even, in the range of
4 to 16.

Click OK button to create array.

NOTE:

If the number of HDDs you select is not compatible with the requirement of the RAID
level, the error message box will pop up.

Figure 210 Error Message Box

You can click Array tab to view the successfully created array.

Summary of Contents for DS-7608NI-I2/8P






























































































































































































































Search results

Summary of Contents for DS-7608NI-I2/8P

Reviews:

HIKVISION DS-7608NI-I2/8P, User Manual, Page: 166 / 221

Search results

Summary of Contents for DS-7608NI-I2/8P

Reviews: