HIKVISION DS-7608NI-I2/8P User Manual Download Page 160

Page: 160 / 221

I Series Network Video Recorder User Manual, 030117NA

159

Figure 198 Packet Export Attention

NOTE:

Up to 1 MB of data can be exported at a time.

12.4.3.

Checking the Network Status

You can check the network status and quick set the network parameters in this interface.

Click the

Status

button on the lower-right corner of the page.

Figure 199 Network Status Checking

If the network is normal, the following message box appears. If the message box appears with
information other than this, click the

Network

button to show the network parameters quick setting

interface.

Figure 200 Network Status Checking Result

12.4.4.

Checking Network Statistics

Check the network status to obtain NVR’s real-time information.

Enter the Network Detection interface, Menu > Maintenance > Net Detect.

Summary of Contents for DS-7608NI-I2/8P






























































































































































































































Search results

Summary of Contents for DS-7608NI-I2/8P

Reviews:

HIKVISION DS-7608NI-I2/8P, User Manual, Page: 160 / 221

Search results

Summary of Contents for DS-7608NI-I2/8P

Reviews: