Home
/
HIKVISION
/
DS-7608NI-I2/8P
/
User Manual

HIKVISION DS-7608NI-I2/8P, User Manual, Page: 149 / 221

Share

Page: 149 / 221

HIKVISION DS-7608NI-I2/8P User Manual Download Page 149

I Series Network Video Recorder User Manual, 030117NA

148

Figure 180 Configure More Settings

4.

Click the

Apply

button to save and exit the interface.

12.2.8.

Configuring HTTPS Port

HTTPS authenticates the Web site and associated Web server that one is communicating with, which
protects against man-in-the-middle attacks. Perform the following steps to set the https port number.

Example:

If the port number is set to 443 and the IP address is set to 192.0.0.64, access the device
by inputting

https://192.0.0.64:443

via the Web browser.

NOTE:

The HTTPS port can be configured only through the Web browser.

1.

Open Web browser, input the IP address of device, and the Web server will select the language
automatically according to the system language and maximize the Web browser.

2.

Input the correct user name and password, and click Login button to log in to the device.

3.

Enter the HTTPS settings interface, Configuration > Remote Configuration > Network Settings >
HTTPS.

4.

Create the self-signed certificate or authorized certificate.

«
...
147
148
149
150
151
...
»

Summary of Contents for DS-7608NI-I2/8P






























































































































































































































Reviews:

No comments