manualshive.com logo in svg

HIKVISION DS-7608NI-I2/8P, User Manual, Page: 146 / 221

Share
Download
HIKVISION DS-7608NI-I2/8P User Manual Download Page 146

I Series Network Video Recorder User Manual, 030117NA 

145 

NOTE: 

For more help, see the help file on the Hik-Connect website at www.hik-connect.com.

 

12.2.5.

 

Configuring NTP Server 

A Network Time Protocol (NTP) Server can be configured on your NVR to ensure the accuracy of the 
system date/time.   

1.

 

Enter the Network Settings interface, Menu > System Configuration > General. 

2.

 

Select the 

NTP 

tab to enter the NTP Settings interface.   

 

Figure 176 NTP Settings Interface 

3.

 

Check the 

Enable NTP

 checkbox to enable this feature. 

4.

 

Configure the following NTP settings: 

•  Interval: 

Time interval between the two synchronizing actions with NTP server, in minutes..   

•  NTP Server: 

IP address of the NTP server. 

•  NTP Port: 

Port of the NTP server. 

5.

 

Click the 

Apply

 button to save and exit the interface.   

NOTE:

 

The time synchronization interval can be set from 1 to 10080 min, and the default 
value is 60 min. If the NVR is connected to a public network, you should use a NTP 
server that has a time synchronization function such as the server at the National Time 
Center (IP Address: 210.72.145.44). If the NVR is set up in a more customized 
network, NTP software can be used to establish an NTP server used for time 
synchronization. 

12.2.6.

 

Configuring SNMP 

You can use SNMP protocol to get device status and parameter related information. 

1.

 

Enter the Network Settings interface, Menu > Configuration > Network. 

2.

 

Select the 

SNMP 

tab to enter the SNMP Settings interface, as shown in Figure 177. 

Summary of Contents for DS-7608NI-I2/8P






























































































































































































































Reviews:

No comments