Home
/
HIKVISION
/
DS-7608NI-I2/8P
/
User Manual

HIKVISION DS-7608NI-I2/8P, User Manual, Page: 143 / 221

Share

Page: 143 / 221

HIKVISION DS-7608NI-I2/8P User Manual Download Page 143

I Series Network Video Recorder User Manual, 030117NA

142

For DS-7700NI-I(I)/P Series NVRs, you need to configure the internal NIC address so that IP
addresses are assigned to the cameras connected to the PoE interfaces.

4.

After having configured the general settings, click Apply button to save the settings.

12.1.1.

Working Mode (DS-96xxNI-I8 Models)

Two 10M/100M/1000M NIC cards are provided and it allows the device to work in the Multi-address and
Net-fault Tolerance modes.

•

Multi-address Mode:

The parameters of the two NIC cards can be configured independently.

Select LAN1 or LAN2 in the NIC type field for parameter settings. Select one NIC card as the
default route, and the data connecting to the extranet will be forwarded through the default route.

•

Net-Fault Tolerance Mode:

The two NIC cards use the same IP address. Select the Main NIC as

LAN1 or LAN2. This way, in case one NIC card fails, the device will automatically enable the other
standby NIC card so as to ensure normal running of the system.

Figure 174 Net Fault-tolerance Working Mode (/I8 NVRs only)

12.2

Configuring Advanced Settings

12.2.1.

Register a HIK-Connect P2P Cloud Service Account

1.

Use the Hik-Connect mobile app (from iOS App Store or Google Play) to create a Hik-Connect P2P
Cloud account to connect Hikvision devices over the Internet.

2.

Click on “Register an Account.”

3.

Check the

Read and Agree

checkbox.

«
...
141
142
143
144
145
...
»

Summary of Contents for DS-7608NI-I2/8P






























































































































































































































Reviews:

No comments