manualshive.com logo in svg

HIKVISION DS-7608NI-I2/8P, User Manual, Page: 142 / 221

Share
Download
HIKVISION DS-7608NI-I2/8P User Manual Download Page 142

I Series Network Video Recorder User Manual, 030117NA 

141 

Chapter 12

 

Network Settings 

12.1

 

Configuring General Settings 

Network settings must be properly configured before operating the NVR over a network. 

1.

 

Enter the Network Settings interface, Menu > Configuration > Network. 

2.

 

Select the General tab. 

 

Figure 173 Network Settings Interface 

3.

 

In the General Settings interface, configure the following settings: Working Mode, NIC Type, IPv4 Address, 
IPv4 Gateway, MTU, and DNS Server. 

NOTES:

 

The valid value MTU range is 500 – 9676.   

 

If the DHCP server is available, you can click the 

DHCP

 checkbox to automatically obtain an IP 

address and other network settings from that server. 

 

Two self-adaptive 10M/100M/1000M network interfaces for DS-9600NI-I8, DS-7700NI-I4, and 
the multi-address and network fault tolerance working modes are configurable.     

 

One self-adaptive 10M/100M/1000M network interface for DS-7700NI-I4/P.   

Summary of Contents for DS-7608NI-I2/8P






























































































































































































































Reviews:

No comments