manualshive.com logo in svg

HIKVISION DS-7608NI-I2/8P, User Manual, Page: 139 / 221

Share
Download
HIKVISION DS-7608NI-I2/8P User Manual Download Page 139

I Series Network Video Recorder User Manual, 030117NA 

138 

 

Figure 170 Plate Search 

4.

 

Select the country from the drop-down list for searching the location of the vehicle plate. 

5.

 

Input the plate No. in the field for search.   

6.

 

Click Search to start searching. The search results of detected vehicle plate pictures are displayed in list or 
chart.   

NOTE: 

Refer to Step 7 and Step 8 of 

Section 10.1 Face Search

 for operation of the search results.       

11.4

 

People Counting 

People Counting calculates the number of people who enter or leave a configured area and creates 
daily/weekly/monthly/annual reports for analysis.     

1.

 

Enter the Counting interface, Menu > VCA Search > Counting. 

2.

 

Select the camera for the people counting.   

3.

 

Select the report type: Daily Report, Weekly Report, Monthly Report, or Annual Report. 

4.

 

Set the statistics time.   

5.

 

Click the Counting button to start people counting statistics.     

Summary of Contents for DS-7608NI-I2/8P






























































































































































































































Reviews:

No comments