HIKVISION DS-7608NI-I2/8P User Manual Download Page 110

Page: 110 / 221

I Series Network Video Recorder User Manual, 030117NA

109

Figure 132 Reboot Attention

Click the

Yes

button in the pop-up attention box.

8.3.3.

Setting Working Device

Enter the Hot Spare settings interface, Menu > Configuration > Hot Spare.

Set the Work Mode to Normal Mode (default).

Check the Enable checkbox to enable the hot spare function.

Enter the IP address and admin password of the hot spare device.

Figure 133 Setting Working Mode for Working Device

Click the

Apply

button to save the settings.

8.3.4.

Managing the Hot Spare System

Enter the Hot Spare Settings interface of the hot spare device, Menu > Configuration > Hot Spare.
The connected working device will be displayed on the device list.

Summary of Contents for DS-7608NI-I2/8P






























































































































































































































Search results

Summary of Contents for DS-7608NI-I2/8P

Reviews:

HIKVISION DS-7608NI-I2/8P, User Manual, Page: 110 / 221

Search results

Summary of Contents for DS-7608NI-I2/8P

Reviews: