manualshive.com logo in svg

HIKVISION DS-7600NXI-K1 Series, User Manual

Share
Download
HIKVISION DS-7600NXI-K1 Series User Manual Download Page 84

Network Video Recorder User Manual 

72 

6.5 Recording Management 

6.5.1 Configure Recording Schedule 

Video recorder will automatically start/stop recording according to the configured schedule. 

Configure Continuous Recording 

Steps   
1. Go to Configuration → Record → Parameter.   
2. Set the continuous main stream/sub-stream recording parameters for the camera. 
3. Go to Configuration → Record → Schedule. 
4. Select recording type as Continuous. 

Configure Event Recording 

You can configure the recording triggered by the normal event or smart event. 

Steps   
1. Go to Configuration → Event. 
2. Configure the event detection and select the cameras to trigger the recording when event 

occurs. 

3. Go to Configuration → Record → Parameter.   
4. Set the continuous main stream/sub-stream recording parameters for the camera. 
5. Go to Configuration → Record → Schedule.   
6. Select recording type as Event. 

Edit Schedule 

Steps   
1. Go to Configuration → Record → Schedule. 

Summary of Contents for DS-7600NXI-K1 Series








































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands