manualshive.com logo in svg

HIKVISION DS-7600NXI-K1 Series, User Manual

Share
Download
HIKVISION DS-7600NXI-K1 Series User Manual Download Page 52

Network Video Recorder User Manual 

40 

●

 

By using the same IP address and two NIC cards share the load of the total bandwidth, 
which enables the system to provide two Gigabit network capacity 

Note 

Working mode is only available for certain models. 

  

NIC Type   

Select NIC type as your desire. 

DHCP   

If the DHCP server is available, you can check Enable DHCP to automatically obtain an IP 
address and other network settings from that server. 

MTU   

The maximum transmission unit (MTU) is the size of the largest network layer protocol data 
unit that can be communicated in a single network transaction. 

Obtain DNS Automatically   

  If DHCP is checked. You can check Obtain DNS Automatically to obtain Preferred DNS 
Server and Alternate DNS Server. 

3. Click Apply. 

6.2.2 DDNS 

Dynamic domain name server (DDNS) maps dynamic user IP addresses to a fixed domain name 
server. 

Before You Start   
Register DynDNS, PeanutHull and NO-IP services with your ISP. 

Steps   
1. Go to Configuration → Network → General → DDNS. 

Summary of Contents for DS-7600NXI-K1 Series








































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands