manualshive.com logo in svg

HIKVISION DS-7100HGHI-F1, User Manual, Page: 83 / 101

Share
Download
HIKVISION DS-7100HGHI-F1 User Manual Download Page 83

6.5 Recording Management

6.5.1 Configure Recording Schedule

Video recorder will automatically start/stop recording according to the configured schedule.

Configure Continuous Recording

Steps

1. Go to Configuration → Record → Parameter .

2. Set the continuous main stream/sub-stream recording parameters for the camera.

3. Go to Configuration → Record → Schedule .

4. Select recording type as Continuous.

Configure Event Recording

You can configure the recording triggered by the normal event or smart event.
Steps

1. Go to Configuration → Event .

2. Configure the event detection and select the cameras to trigger the recording when event

occurs.

3. Go to Configuration → Record → Parameter .

4. Set the continuous main stream/sub-stream recording parameters for the camera.

5. Go to Configuration → Record → Schedule .

6. Select recording type as Event.

Edit Schedule

Steps

1. Go to Configuration → Record → Schedule .

Digital Video Recorder User Manual

69

Summary of Contents for DS-7100HGHI-F1






































































































Reviews:

No comments