manualshive.com logo in svg

HIKVISION DS-5504HMI series, User Manual

Share
Download
HIKVISION DS-5504HMI series User Manual Download Page 59

User Manual of Mobile Digital Video Recorder 

58 

 

Figure 8. 7

 

Import/Export Configuration Files 

 

2.

 

Click the 

Export

 button to export configuration files to the USB device. 

3.

 

To import the configuration file, connect a USB device on which the configuration file is stored to the mobile DVR, and 

then click the 

Import

 button. Reboot the device to activate the new settings after the importing process is complete. 

 

The configuration file should be stored on the root directory of the USB device. 

8.2.5

 

Viewing System Information 

Steps: 

1.

 

Enter the System Information interface. 

Menu>Maintenance>Information 

 

Figure 8. 8

 

System Information 

 

2.

 

You can view the device name, model, serial No. , firmware version, encoding version and panel version. 

8.2.6

 

Backup Device 

Purpose: 

You can view the status and the free space/capacity of the connected USB or eSATA backup device. And you can also format 

Summary of Contents for DS-5504HMI series

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands