Face Recognition Terminal
Quick Start Guide
UDB
Ground
Bottom Cover
Bracket
Bottom Screw
M6×65 Expension Bolt
1
2
3
Before you start:
Make sure the ground surface has drilled
holes for device installation.
Steps:
1. Remove the two bottom screws (2-SC-KM3×5B-JMF) on
both sides of the bottom cover. And remove the bottom
cover.
2. Align the device with the drilled holes on the ground and
insert 3 supplied expension bolts (M6×65). Make sure the
expension bolts are higher than the ground.
3. Secure the expension bolts with nuts。
4. Install the bottom cover back on the device with 2 bottom
screws.
The actual device
appearance varies
according to
different models.
The device should be installed on the concrete surface or other
non-flammable surfaces.
The device supports plug & play. You can put the device on the
ground and start operation after powering on.
2
Installation
The figures are for reference only.
The Wiegand terminal here is a Wiegand input terminal. You should set
the device’s Wiegand direction to “Input”. If you should connect to
an access controller, you should set the Wiegand direction to “Output”.
For details, see the user manual.
The power supply should be 12 VDC/3 A, 36 W.
IN2
Yellow/Orange
Yellow/Blue
Yellow/Purple
Purple
Grey
Orange
Brown
White
Green
Yellow/Brown
Power
Yellow/Red
(NC)
(NO)
Yellow/Black
Alarm Input Device
Alarm Output Device
Alarm Output Device
A3
A1
A2
A4
A5
A6
B1
B2
B3
B4
B5
B6
WG_OK
WG_ERR
BUZZER
12 V
Power Supply
Wiegand
Car
d R
ead
er
Wiegand
Alarm Input
Alarm Output
Tag 2
Tag 4
Tag 2
Tag 4
RS-48
5
Net
w
ork Int
er
face
Debugging P
or
t
(For Debuggin Only)
Door Lock Int
er
face
Wiegand
Alar
m Input
/Out
put
Pow
er Input
USB Int
er
face 2
USB Int
er
face 1
Device
The wiring diagram of tag 2 and 4 on the left is shown below:
© 2020 Hangzhou Hikvision Digital Technology Co., Ltd. All rights reserved.
This Manual is the property of Hangzhou Hikvision Digital Technology Co., Ltd. or its
affiliates (hereinafter referred to as “Hikvision”), and it cannot be reproduced, changed,
translated, or distributed, partially or wholly, by any means, without the prior written
permission of Hikvision. Unless otherwise expressly stated herein, Hikvision does not
make any warranties, guarantees or representations, express or implied, regarding to the
Manual, any information contained herein.
About this Manual
The Manual includes instructions for using and managing the Product. Pictures, charts,
images and all other information hereinafter are for description and explanation only. The
information contained in the Manual is subject to change, without notice, due to firmware
updates or other reasons. Please find the latest version of this Manual at the Hikvision
website (https://www.hikvision.com/).
Please use this Manual with the guidance and assistance of professionals trained in
supporting the Product.
Trademarks Acknowledgement
and other Hikvision’s trademarks and logos are the properties of Hikvision in
various jurisdictions.
Other trademarks and logos mentioned are the properties of their respective owners.
LEGAL DISCLAIMER
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS MANUAL AND THE
PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, ARE PROVIDED
“AS IS” AND “WITH ALL FAULTS AND ERRORS”. HIKVISION MAKES NO WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTO
-
RY QUALITY, OR FITNESS FOR A PARTICULAR PURPOSE. THE USE OF THE PRODUCT BY YOU
IS AT YOUR OWN RISK. IN NO EVENT WILL HIKVISION BE LIABLE TO YOU FOR ANY SPECIAL,
CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS,
DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA,
CORRUPTION OF SYSTEMS, OR LOSS OF DOCUMENTATION, WHETHER BASED ON BREACH
OF CONTRACT, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY, OR OTHERWISE, IN
CONNECTION WITH THE USE OF THE PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF
THE POSSIBILITY OF SUCH DAMAGES OR LOSS.
YOU ACKNOWLEDGE THAT THE NATURE OF INTERNET PROVIDES FOR INHERENT SECURITY
RISKS, AND HIKVISION SHALL NOT TAKE ANY RESPONSIBILITIES FOR ABNORMAL
OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER-ATTACK,
HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER,
HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.
YOU AGREE TO USE THIS PRODUCT IN COMPLIANCE WITH ALL APPLICABLE LAWS, AND
YOU ARE SOLELY RESPONSIBLE FOR ENSURING THAT YOUR USE CONFORMS TO THE
APPLICABLE LAW. ESPECIALLY, YOU ARE RESPONSIBLE, FOR USING THIS PRODUCT IN A
MANNER THAT DOES NOT INFRINGE ON THE RIGHTS OF THIRD PARTIES, INCLUDING
WITHOUT LIMITATION, RIGHTS OF PUBLICITY, INTELLECTUAL PROPERTY RIGHTS, OR DATA
PROTECTION AND OTHER PRIVACY RIGHTS. YOU SHALL NOT USE THIS PRODUCT FOR ANY
PROHIBITED END-USES, INCLUDING THE DEVELOPMENT OR PRODUCTION OF WEAPONS
OF MASS DESTRUCTION, THE DEVELOPMENT OR PRODUCTION OF CHEMICAL OR
BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED TO ANY NUCLEAR
EXPLOSIVE OR UNSAFE NUCLEAR FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS
ABUSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW,
THE LATER PREVAILS.
Data Protection
During the use of device, personal data will be collected, stored and processed. To protect
data, the development of Hikvision devices incorporates privacy by design principles. For
example, for device with facial recognition features, biometrics data is stored in your
device with encryption method; for fingerprint device, only fingerprint template will be
saved, which is impossible to reconstruct a fingerprint image.
As data controller, you are advised to collect, store, process and transfer data in
accordance with the applicable data protection laws and regulations, including without
limitation, conducting security controls to safeguard personal data, such as, implementing
reasonable administrative and physical security controls, conduct periodic reviews and
assessments of the effectiveness of your security controls.
Scan the QR code to get the user manual for detailed information.
Note that mobile data charges may apply if Wi-Fi is unavailable.
Use only power supplies listed in the user instructions:
Model
Manufacturer
Standard
C2000IC12.0-24P-DE
C2000IC12.0-24P-GB
MOSO Power Supply Technology Co., Ltd. CEE
MOSO Power Supply Technology Co., Ltd. BS
ADS-24S-12 1224GPG Shenzhen Honor Electronic Co., Ltd.
CEE
Installation Environment:
If installing the device indoors, the device should be at least 2 meters
away from the light, and at least 3 meters away from the window or the
door.
Make sure the environment illumination is more than 100 Lux.
Direct Sunlight
Direct Sunlight
through Window
Indirect Sunlight
through Window
Backlight
10Lux
＞1200Lux
100~850Lux
3m
2m
Close to Light
1
Appearance
3.1
Device Wiring (Without Secure Door Control Unit)
165 mm
13
98
.9
5 mm
172 mm
250.71 mm
46 mm
144.71 mm
37 mm
185.91 mm
13
47
.2
8 mm
Touch Screen
IR Light
IR Light
Camera
White Light
Thermographic
Module
69.96 mm
Draf
t Draf
t Draf
t Draf
t
Draf
t Draf
t Draf
t Draf
t
Draf
t Draf
t Draf
t Draf
t Draf
t Draf
t Draf
t Draf
t
Draf
t Draf
t Draf
t Draf
t Draf
t Draf
t Draf
t Draf
t
Draf
t Draf
t Draf
t Draf
t Draf
t Draf
t Draf
t Draf
t
Draf
t Draf
t Draf
t Draf
t Draf
t Draf
t
