manualshive.com logo in svg

HIKVISION 607 Series, User Manual, Page: 52 / 163

Share
Download
HIKVISION 607 Series User Manual Download Page 52

607 Series Face Recognition Terminal

 

User Manual

 

42 

 

Note:

 The device will call the master station in priority when tap 

. 

6.8.3

 

Calling Device from iVMS-4200 Client Software 

Steps: 
1.

 

Get the client software from the supplied disk or the official website, and install the software 
according to the prompts. 

2.

 

Run the client software and the control panel of the software pops up. 

3.

 

Click Device Management to enter the Device Management interface. 

4.

 

Add the device to the client software. 

Note:

 For details about adding device, see 7.3.1 Adding Access Control Device. 

5.

 

Enter the Live View page and double-click the added device to start live view. 

Note:

 For details about operations in the Live View page, see 7.12 Live View. 

6.

 

Right click the live view image to open the right-click menu. 

7.

 

Click Start Two-Way Audio to start two-way audio between the device and the client software. 

6.8.4

 

Calling Indoor Station from Device 

Steps: 
1.

 

Get the client software from the supplied disk or the official website, and install the software 
according to the prompts. 

2.

 

Run the client software and the control panel of the software pops up. 

3.

 

Click Device Management to enter the Device Management interface. 

4.

 

Add the indoor station and the device to the client software. 

Note:

 For details about adding device, see 7.3.1 Adding Access Control Device. 

5.

 

Link a user to an indoor station and set a room No. for the indoor station. 

6.

 

Tap 

  on the authentication page of the device. 

7.

 

Input the room No. on the dial page and tap 

  to call the indoor station. 

8.

 

After the indoor station answers the call, you can start two-way audio with the indoor station. 

 

Summary of Contents for 607 Series




































































































































































Reviews:

No comments