HIKVISION 607 Series User Manual Download Page 46 | Manualshive

Page: 46 / 163

HIKVISION 607 Series User Manual Download Page 46

607 Series Face Recognition Terminal

User Manual

36

If you select Custom, you can customize the start time and the end time for search.

5.

Tap

to start search.

The result will be displayed in the page.

6.6.3

Importing/Exporting Data

Purpose:
On the Transfer page, you can export the attendance data, the user data, the user picture, the
access control parameter, the captured picture, and the exception data to the USB flash drive. You
can also import the user data, the user picture, and the access control parameter from the USB
flash drive.
Tap Transfer on the Home page to enter the Transfer page.

Exporting Data

Steps:
1.

Plug a USB flash drive in the device.

2.

On the Transfer page, tap Export Att. Data, Export User Data, Export Face Pic., Export Access
Control Param., or Export Captured Pic.

3.

Tap Yes on the pop-up page and the data will be exported from the device to the USB flash
drive.

Notes:



The supported USB flash drive format is FAT 32.

«
...
44
45
46
47
48
...
»

Summary of Contents for 607 Series




































































































































































Reviews:

No comments