manualshive.com logo in svg

HIKVISION 607 Series, User Manual, Page: 137 / 163

Share
Download
HIKVISION 607 Series User Manual Download Page 137

607 Series Face Recognition Terminal

 

User Manual

 

127 

 

 

Remain closed. 

7.

 

Click 

/   to open or close the door. 

Or click 

/   to set the door status as remain open or remain closed. 

Note: 

One camera can be linked to only one access control point; Different cameras can be linked 

to the same access control point. 

7.13

 

Arming Control 

Purpose: 
You can arm or disarm the device. After arming the device , the client can receive the alarm information from the 
device. 
Steps: 
1.

 

Click Tool->Device Arming Control to pop up the Device Arming Control window. 

2.

 

Arm the device by checking the corresponding checkbox.   
Then the alarm information will be auto uploaded to the client software when alarm occurs. 

 

7.14

 

Time and Attendance 

Purpose: 
The  Time  and  Attendance  module  provides  multiple  functionalities,  including  shift  schedule 
management, attendance handling, attendance statistics and other advanced functions. 
Before you start: 
You  should  add  organization  and  person  in  Access  Control  module.  For  details,  refer  to  Chapter 
7.4.1 Adding Organization and Chapter 7.5.1 Adding Person. 
Perform the following steps to access the Time and Attendance module. 

Click 

  to enter the Time and Attendance module as follows: 

Summary of Contents for 607 Series




































































































































































Reviews:

No comments