HikRobot MV-CL042-91CC User Manual Download Page 89

Page: 89 / 120

Camera Link Line Scan Camera

User Manual

11.4 File Access Control

The file access function allows you to export or import the camera’s parameters, LUT and user
PRNUC, and user FPNC in the mfa format. Currently, the camera supports User Set 1/2/3, LUT
Luminance 1/2/3, User PRNUC 1/2/3, and User FPNC.



The file access control function and specific device features that can be imported and exported
may differ by camera models.



Make sure that you have stopped acquisition before using this function.



Make sure that the firmware is same when exporting or importing files between two cameras.

Steps:

Select the camera in the device list.

Click

to open the File Access interface.

Figure 11-4

File Access

Select Device Feature according to actual demands.

Figure 11-5

Select Device Feature

Click Import or Export to import or export files.

Summary of Contents for MV-CL042-91CC

























































































































Search results

Summary of Contents for MV-CL042-91CC

Reviews:

Related manuals for MV-CL042-91CC

Brands by name

Popular brands

HikRobot MV-CL042-91CC, User Manual

Search results

Summary of Contents for MV-CL042-91CC

Reviews:

Related manuals for MV-CL042-91CC

Brands by name

Popular brands