HikRobot MV-CL042-91CC User Manual Download Page 30 | Manualshive

Page: 30 / 120

background image

Camera Link Line Scan Camera

·

User Manual

21

Trigger Mode Parameter

Parameter Value

Principle

the internal configured value.
Only after the frame trigger
signal arrives, the line trigger
signal will work.

7.6 Set Trigger Source

Apart from the internal trigger mode, you need to set the trigger source for line trigger or frame
trigger if their trigger signals come from external signals. Six types of trigger sources are available,
including software trigger, hardware trigger, shaft encoder control, frequency converter control,
frame grabber trigger control, and free trigger.

Table 7-2

External Trigger Mode Principle and Parameter

Trigger
Source

Supported
Trigger Mode

Parameter

Parameter
Value

Principle

Software
Trigger

Frame trigger

Acquisition
Control >
Trigger Source

Software

The software sends trigger signal to
the camera via Camera Link
interface to acquire images.

Hardware
Trigger

Frame trigger or
line trigger

Acquisition
Control >
Trigger Source

Specific Line

External device connects camera via
camera I/O interface. External
device sends trigger signal to
camera to acquire images.

Shaft Encoder
Control

Line trigger

Acquisition
Control >
Trigger Source

Encoder
Module Out

This trigger source uses shaft
encoder module to receive signal A
and signal B with phase difference.
After internal computing of the
module, the outputted signal can be
used as camera’s trigger signal.

Frequency
Converter
Control

Frame trigger or
line trigger

Acquisition
Control >
Trigger Source

Frequency
Converter

This trigger source allows different
frequency between trigger camera
signal and required input signal.

Frame
Grabber
Trigger
Control

Frame trigger or
line trigger

Acquisition
Control >
Trigger Source

CC1/CC2/CC3/C
C4

Frame grabber triggers camera to
acquire images by sending signal via
Camera Link cable.

«
...
28
29
30
31
32
...
»

Summary of Contents for MV-CL042-91CC

























































































































Reviews:

No comments

Related manuals for MV-CL042-91CC

Brand: Canon Pages: 49

Brand: Olympus Pages: 2

Brand: Chang Rui Technology Pages: 40

Brand: Abocom Pages: 1

Brand: Santec Pages: 8

Toy Story DJ016TS

Brand: LEXIBOOK Pages: 48

Brand: Genesis CCTV Pages: 3

Brand: Uniden Pages: 28

Brand: Ultrak Pages: 36

Brand: BTECH Pages: 2

KB20 - 35 Mm Camera

Brand: Kodak Pages: 21

Brand: Air Live Pages: 97

Brand: Easypix Pages: 2

Brand: Insignia Pages: 38

Brand: Patroleyes Pages: 16

PT12X-SDI-GY-G2

Brand: PTZOptics Pages: 52

Brand: D-Link Pages: 72

Brand: YURAKU Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands