HikRobot MV-CL042-91CC User Manual Download Page 29 | Manualshive

Page: 29 / 120

background image

Camera Link Line Scan Camera

·

User Manual

20

7.5 Set Trigger Mode

The camera has 4 types of trigger modes, including internal trigger mode, line trigger mode, frame
trigger mode, and line + frame trigger mode.

Table 7-1

Trigger Mode Principle and Parameter

Trigger Mode Parameter

Parameter Value

Principle

Internal
Trigger Mode

Acquisition
Control >
Trigger Selector
and Trigger
Mode

Trigger Selector =Line Start

Trigger Mode = Off

and

Trigger Selector =Frame Burst Start

Trigger Mode =Off

The camera itself generates the
triggering signals of this mode,
and you can adjust the line rate
parameters according to actual
demand.

Line Trigger
Mode

Acquisition
Control >
Trigger Selector
and Trigger
Mode

Trigger Selector =Line Start

Trigger Mode = On

and

Trigger Selector =Frame Burst Start

Trigger Mode = Off

Under this mode, the
frequency of the external line
trigger control signal
determines the line rate, and
only one line is exposed when
a trigger signal is input.

Frame Trigger
Mode

Acquisition
Control >
Trigger Selector
and Trigger
Mode

Trigger Selector =Frame Burst Start

Trigger Mode = On

and

Trigger Selector =Line Start

Trigger Mode = Off

After receiving frame trigger
signal, camera will start to
expose and generate image
data. The camera outputs
images according to current
settings. You do not need to
set line trigger signal. For max.
line rate that camera supports,
please refer to the camera
specification.

Line + Frame
Trigger Mode

Acquisition
Control >
Trigger Selector
and Trigger
Mode

Trigger Selector =Line Start

Trigger Mode =On

and

Trigger Selector =Frame Burst Start

Trigger Mode =On

In this mode, the camera's
external frame trigger signal
and line trigger signal is
required. The line number of a
frame is controlled by the
frame height register, and the
line rate is controlled by an
externally supplied line trigger
signal, while being limited by

«
...
27
28
29
30
31
...
»

Summary of Contents for MV-CL042-91CC

























































































































Reviews:

No comments

Related manuals for MV-CL042-91CC

MACRO SPEEDLITE MR-14EX

Brand: Canon Pages: 2

Macro ring lite MR-14EX II

Brand: Canon Pages: 87

Brand: Laon People Pages: 46

Brand: Q-See Pages: 2

Brand: Loocam Pages: 8

Brand: AIPTEK Pages: 60

M.Zuiko Digital ED 150-400mm F4.5 TC1.25x IS...

Brand: Olympus Pages: 202

Brand: Genesis CCTV Pages: 3

XF10-24mmF4 R OIS

Brand: FujiFilm Pages: 136

Brand: TytoCare Pages: 76

Brand: Crux Pages: 5

Alvium 1800 U-500c

Brand: Allied Vision Technologies Pages: 97

Brand: GKB Pages: 8

Brand: Sunrex Pages: 5

Brand: Conceptronic Pages: 31

Brand: MMC Pages: 5

Brand: nedis Pages: 92

Brand: AIPTEK Pages: 134

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands