HIKOKI C 3607DWA Handling Instructions Manual Download Page 27

Page: 27 / 32

TROUBLESHOOTING GUIDE

WARNING

Use the inspections in the table below if the tool does not operate normally. If this does not remedy the

problem, consult your dealer or the HiKOKI Authorized Service Center.

1. Power

tool

Symptom

Possible cause

Remedy

Tool doesn’t run

No remaining battery power

Charge the battery.

Battery isn’t fully installed.

Push the battery in until you hear a click.

Tool suddenly stopped

Tool was overburdened

Get rid of the problem causing the

overburden.

Overload protection is in operation.
The battery is overheated.

Let the battery cool down.

Cannot be inclined

The incline lever is not loosened.

Try inclining after loosening the incline

lever. Tighten the loosened parts after

making the necessary adjustments.

Doesn’t cut well

The saw blade is worn or missing teeth.

Replace with a new saw blade.

The bolt is loose.

Firmly tighten the bolt.

The saw blade is installed backwards.

Install the saw blade in the proper

direction.

Switch can’t be pulled

The lock-o

ﬀ

button is not pushed in

enough.

Push the lock-o

ﬀ

button in all the way.

Sawdust discharge is poor Sawdust has accumulated in the saw

cover.

Remove the sawdust inside the saw cover.

Battery cannot be installed Attempting to install a battery other than

that speci

ed for the tool.

Please install a multi volt type battery.

2. Charger

Symptom

Possible cause

Remedy

The charge indicator lamp

is rapidly

ickers purple,

and battery charging

doesn’t begin.

The battery is not inserted all the way.

Insert the battery

rmly.

There is foreign matter in the battery

terminal or where the battery is attached.

Remove the foreign matter.

The charge indicator lamp

blinks red, and battery

charging doesn’t begin.

The battery is not inserted all the way.

Insert the battery

rmly.

The battery is overheated.

If left alone, the battery will automatically

begin charging if its temperature

decreases, but this may reduce battery

life. It is recommended that the battery be

cooled in a well-ventilated location away

from direct sunlight before charging it.

Battery usage time is short

even though the battery is

fully charged.

The battery’s life is depleted.

Replace the battery with a new one.

00Book̲C3607DWA̲AUST.indb 27

2022/06/10 14:51:34

Summary of Contents for C 3607DWA

































Search results

Summary of Contents for C 3607DWA

Reviews:

Related manuals for C 3607DWA

Brands by name

Popular brands

HIKOKI C 3607DWA, Handling Instructions Manual

Search results

Summary of Contents for C 3607DWA

Reviews:

Related manuals for C 3607DWA

Brands by name

Popular brands