17
English
Dismounting the saw blade
27
8
Mounting the Saw Blade
28
8
Charging a USB device from a
electrical outlet
29
-
a
9
Charging a USB device and battery
from a electrical outlet
29
-
b
9
How to recharge USB device
30
9
When charging of USB device is
completed
31
9
Selecting accessories
―
94
(*1) About the mode select function
Each time the mode selector switch is pushed, the
operation mode changes.
When Silent mode is selected, the Silent mode indicator
lamp lights up.
Silent mode reduces maximum motor RPM enabling
e
ffi
cient work with less noise.
If the load increases while the motor is operating in
Silent mode, it automatically changes to Power mode.
Additionally, if the load decreases again, it automatically
returns to Silent mode.
In Power mode, no change is made to Silent mode even
when the load decreases.
Mode
No
-
load speed
Power
5000 /min
Silent
2600 /min
NOTE
○
The mode will only change after a battery is installed and
the switch is pulled once.
○
The current mode will be maintained even if the switch is
on/o
ff
, or the battery is removed/reinserted.
(*2) Attaching the Hook
The hook can be used to hang up the unit
temporarilyduring operations. (
Fig. 22
)
CAUTION
The hook should never be used to hang the unit on your
person.
When using the hook, check to make sure that the main
unit will not slip and fall, or become unstable by the wind,
etc.
Never hang the unit from your belt or trousers as this
could cause accidents.
How to make the batteries perform longer.
(1) Recharge the batteries before they become completely
exhausted.
When you feel that the power of the tool becomes
weaker, stop using the tool and recharge its battery. If
you continue to use the tool and exhaust the electric
current, the battery may be damaged and its life will
become shorter.
(2) Avoid recharging at high temperatures.
A rechargeable battery will be hot immediately after
use. If such a battery is recharged immediately after
use, its internal chemical substance will deteriorate, and
the battery life will be shortened. Leave the battery and
recharge it after it has cooled for a while.
CAUTION
○
If the battery is charged while it is heated because
it has been left for a long time in a location subject to
direct sunlight or because the battery has just been
used, the charge indicator lamp of the charger lights
for 0.3 seconds, does not light for 0.3 seconds (o
ff
for
0.3 seconds). In such a case,
fi
rst let the battery cool,
then start charging.
○
When the charge indicator lamp
fl
ickers (at 0.2
-
second
intervals), check for and take out any foreign objects in
the charger’s battery connector. If there are no foreign
objects, it is probable that the battery or charger is
malfunctioning. Take it to your authorized Service Center.
○
Since the built
-
in micro computer takes about
3 seconds to con
fi
rm that the battery being charged with
UC18YSL3 is taken out, wait for a minimum of 3 seconds
before reinserting it to continue charging. If the battery
is reinserted within 3 seconds, the battery may not be
properly charged.
MOUNTING AND OPERATION
Action
Figure
Page
Inclined cutting using the guide
(+45° direction) (sold separately)
9
3
Fine tuning of parallelism
10
3
Fine tuning of perpendicularity
11
3
Fine tuning of guide piece position
12
3
Adjusting the cutting depth
13
4
Cutting line
14
4
Switch operation
15
4
About the mode select function (*1)
16
4
Remaining battery indicator
17
4
Using the LED light
18
4
Attaching the guide
19
5
Attaching the dust collection adapter
(sold separately)
20
5
Attaching the
fl
uorine plate
(sold separately)
21
5
Attaching the hook (*2)
(sold separately)
22
6
Removing and inserting the battery
23
6
Charging
24
6
Cutting at right angles
25
6
Inclined cutting (+45° direction)
26
7
00Book̲C3605DA̲Asia.indb 17
00Book̲C3605DA̲Asia.indb 17
2018/12/21 14:39:16
2018/12/21 14:39:16
