HIAB Hooklift Multilift XR S Series User And Maintenance Manual Download

Page: 6 / 160

4/2018

113175421

XR14S/16S/18S/21S/26S/30S

Hooklift Multilift XR S

User Manual

MULTILIFT XR21S hooklift equipment

Note!

Cargotec Finland Oy reserves the right to change specifications, equipment, operating and

maintenance instructions without prior notice.

GENERAL DESCRIPTION

MULTILIFT XR hooklift equipment is an exchange container loading and unloading device

mounted on a truck chassis. An experience of over 60 years is a proof of the reliability and

versatility of the equipment all over the world.

CE Statement of Conformity

Cargotec Finland Oy Multilift has been an ISO 9001 certified company since 1995 and

since 2002 the company has complied with the ISO 14001 environmental standard.

Multilift guarantees that the equipment contained within this manual conforms with the

EC Machine Directive.

Cargotec Finland Oy

Multilift

Raisio

Finland

2018

Summary of Contents for Hooklift Multilift XR S Series

































































































































































Search results

Summary of Contents for Hooklift Multilift XR S Series

Reviews:

Related manuals for Hooklift Multilift XR S Series

Brands by name

Popular brands

HIAB Hooklift Multilift XR S Series, User And Maintenance Manual

Search results

Summary of Contents for Hooklift Multilift XR S Series

Reviews:

Related manuals for Hooklift Multilift XR S Series

Brands by name

Popular brands