HIAB Hooklift Multilift XR S Series User And Maintenance Manual Download

Page: 25 / 160

4/2018

Hooklift Multilift XR S

User Manual

113175421

XR14S/16S/18S/21S/26S/30S

Tipping

If the container overhang is too much, the rear end of the container will touch the ground

when tipping and the container, truck or hooklift equipment will be damaged.

In very cold weather the load might freeze tight on the container. In that case it must be

freed before tipping. Note that the load might come out in large chunks!

NEVER TIP UNDER THE FOLLOWING CIRCUMSTANCES:

• Container is top heavy at the front end or at either side.

• Load is frozen or only partially loose

• Ground is slippery or uneven

• Strong side wind, over 20 m/s [44 mph (70 km/h)]

If it is necessary to drive with the tipping device up, pay attention to the vicinity regarding

the height of the hooklift equipment / container with respect to the surroundings like bridges,

tunnels and overhead power lines! Drive slowly and be extra careful.

If the tipping angle is changed during driving, the gearbox bears an extra burden, and the

truck can make unexpected motions on a slippery surface.

Summary of Contents for Hooklift Multilift XR S Series

































































































































































Search results

Summary of Contents for Hooklift Multilift XR S Series

Reviews:

Related manuals for Hooklift Multilift XR S Series

Brands by name

Popular brands

HIAB Hooklift Multilift XR S Series, User And Maintenance Manual

Search results

Summary of Contents for Hooklift Multilift XR S Series

Reviews:

Related manuals for Hooklift Multilift XR S Series

Brands by name

Popular brands