manualshive.com logo in svg

HIAB Hooklift Multilift XR S Series, User And Maintenance Manual

Share
Download
HIAB Hooklift Multilift XR S Series User And Maintenance Manual Download Page 153

153

4/2018 

113175421

XR14S/16S/18S/21S/26S/30S

Hooklift Multilift XR S

Service Manual

 

•   That adjustment of pressure relief valve settings and where applicable load 

 

 

limiting valve settings is prohibited and will invalidate the warranty.

 

•   Miscellaneous

   ………………………………………………………………………………………..

   ………………………………………………………………………………………..

Owner’s Warranty

This Owner’s Warranty (hereinafter referred to as the ”Warranty”) applies to the products 

listed on the delivery card (hereinafter referred to as the ”Products”) which accompanies 

it. This Warranty is issued by the company that has sold the Product (hereinafter referred 

to as the ”Seller”). The Warranty cannot be invoked against any other party than the Seller.

1 Warranty

1.1  The Seller warrants that the Products as listed in the delivery card, with the 

 

exceptions stated below, are free from defects in material and manufacture. The 

 

Warranty period is twenty-four (24) months from the date of delivery of the Products, 

 

[but shall never exceed thirty (30) months from the date of delivery from factory].

 

•   For demountable body systems the Warranty periods shall only apply in normal 

 

 

usage of the Product, meaning in the maximum 4 000 platform changes per 24 

 

 

months. In case the Product is used more excessively, the duration of the 

 

 

Warranty period must be negotiated separately and if no agreement is entered 

 

 

into the period in this paragraph applies.

Summary of Contents for Hooklift Multilift XR S Series

































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands