HIAB Hooklift Multilift XR S Series Page 150 User And Maintenance Manual Download

Page: 150 / 160

150

4/2018

113175421

XR14S/16S/18S/21S/26S/30S

Hooklift Multilift XR S

Service Manual

Periodical Service

The following services are recommended to be done on XR devices by an authorised

Multilift Service Point:

  •   delivery service in connection with the commissioning of the device
  •   first service after 1 - 3 months after commissioning
  •   annual service:

at 12 months interval in normal use (0 -15 platform changes a day)

at 6 months interval in 2-shift use (16 – 30 platform changes a day)

at 3 months interval in 3-shift use (over 30 platform changes a day)

As running hours the service should be done at 180 – 200 hours interval.

Environmental notice

Appropriate disposal of used oils, lubricants, discarded parts and other used

material.

Recycling after service life

When a device is discarded, all of its components shall be recycled and

disposed of in accordance with valid decrees and regulations.

Summary of Contents for Hooklift Multilift XR S Series

































































































































































Search results

Summary of Contents for Hooklift Multilift XR S Series

Reviews:

Related manuals for Hooklift Multilift XR S Series

Brands by name

Popular brands

HIAB Hooklift Multilift XR S Series, User And Maintenance Manual

Search results

Summary of Contents for Hooklift Multilift XR S Series

Reviews:

Related manuals for Hooklift Multilift XR S Series

Brands by name

Popular brands