HIAB Hooklift Multilift XR S Series Page 147 User And Maintenance Manual Download

Page: 147 / 160

147

4/2018

113175421

XR14S/16S/18S/21S/26S/30S

Hooklift Multilift XR S

Service Manual

Optional sensors:

219

Crane body on

Front lock left

Body on

, Ø18 or Ø30 NO or NC

220

Front lock right

Arms out,

load cover system UK /

Bogie blocking on

Ø18 or Ø30 NO or NC

313

Main cylinder protection

, tilt indicator

314

Fast speed tipping

Hook safety lock

, tilt indicator

321

Pull limiter (DE)

Locking beam

, Ø18 NO

322

URB in

, Ø18 NO

323

URB out

Bogie blocking on

, Ø18 NO

LUBRICATION

Lubricate all the lubrication points at max 3 month intervals. A more recommended lubrication

interval would be 1 month.

Note!

The hooklift equipment contains plastic surface slide bearings.

Use LITHIUM based general lubrication grease (EP2).

Molybden based lubricant shortens the service life of the bearings.

If the hooklift is equipped with a central lubrication system, this will need to be checked

according to the manufacturer’s instructions.

Summary of Contents for Hooklift Multilift XR S Series

































































































































































Search results

Summary of Contents for Hooklift Multilift XR S Series

Reviews:

Related manuals for Hooklift Multilift XR S Series

Brands by name

Popular brands

HIAB Hooklift Multilift XR S Series, User And Maintenance Manual

Search results

Summary of Contents for Hooklift Multilift XR S Series

Reviews:

Related manuals for Hooklift Multilift XR S Series

Brands by name

Popular brands