HIAB Hooklift Multilift XR S Series Page 125 User And Maintenance Manual Download

Page: 125 / 160

125

4/2018

113175421

XR14S/16S/18S/21S/26S/30S

Hooklift Multilift XR S

Service Manual

Exit /

Off 1

OK /

Off 2

>>>

How to change the backlight setting of the buttons,

2GCC

The illumination strength of the backlight is set in the cab controller software. The buttons

to access the software and operations in the menu are as follows:

Note:

The first two buttons on

top of the cab controller are

the access buttons to the

software.

Normally these buttons are

identified as body locks

closed and body locks open.

The procedure of setting the illumination strength of the backlight is the following:

Press the first row buttons simultaneously for 10

seconds.

“

C002

” can be seen in the display while pressing the

buttons.

System will make 2 short beeps and all red LEDs will

be shortly lit.

A text “

tESt

” is shown in the display.

Press the top button on right (

locks open

button).

Sub menu up

(fast speed)

Sub menu down

(hook safety lock)

Press

10 s

Summary of Contents for Hooklift Multilift XR S Series

































































































































































Search results

Summary of Contents for Hooklift Multilift XR S Series

Reviews:

Related manuals for Hooklift Multilift XR S Series

Brands by name

Popular brands

HIAB Hooklift Multilift XR S Series, User And Maintenance Manual

Search results

Summary of Contents for Hooklift Multilift XR S Series

Reviews:

Related manuals for Hooklift Multilift XR S Series

Brands by name

Popular brands