HIAB 410K PRO Operator'S Manual Download Page 74

Page: 74 / 82

8.8. Troubleshooting

8.8.1. Main fuses

If the microprocessor detects a fault, this must be rectified immediately.

Fault

Probable

cause

Action

The safety system does not work
at all

The indicator light next to On/Off
button on the user panel is not lit,
even if you press On/Off

Defective
fuses

1. Replace faulty fuses in the:

- vehicle
- standard box
- relay box
(See Description, Components,
Fuse, Location)

2. Check all the cable connections

Description

Components

Fuse

Location

System main fuse

Relay Box, Standard Box,
Oil Cooler

40 A

Located on the
vehicle, where the
crane is mounted

Fuse for all components
connected to the standard
box

Hydraulic control valve,
user panel, extended box.
Truck warning interface

10 A

Located inside the
standard box

Fuse for all components
controlled by the relay
box

Work lights, solenoid
valves

15 A

Located inside the
relay box

8.8.2. Faults on the crane

Faults in the crane must be rectified immediately.

DANGER

• Only correct yourself the faults that according to the table you may rectify.
• Follow the instructions exactly!
• All other faults must be corrected by personnel in a Hiab authorised service

workshop!

Fault

Probable cause

Action

Crane does not react to the
controls.

Indicator lamps light up on the User
Interface.

The crane is in an
OLP situation

Perform movements to
reduce the load moment. If
necessary, release OLP.

Maintenance and Service

HIAB 410K PRO

Summary of Contents for 410K PRO



















































































Search results

Summary of Contents for 410K PRO

Reviews:

HIAB 410K PRO, Operator'S Manual, Page: 74 / 82

Search results

Summary of Contents for 410K PRO

Reviews: